![]() Like I say, if it was mine, I'd only change the pulley, but buy in the other parts, ready to do the full job, if and when the time comes. Here is a video link with my bike with a 10 degree advanced cam timing. I have also advanced cam timing as much as 10 degrees. Softail, Dyna & V-Rod Oxygen Sensor Wrench 755 Details. OEM Rivets for Saddlebag or Tour Pak Latches & Hinges Tool 754 Details. Would be different if it was the front pulley that had gone, because it would be pulled down anyway to change that, and no point in skimping then. On a Harley engine, 4 degrees equals a movement about 250 - 350 RPM. Sort by Name Sort by Price Sort by Date Sort by Popularity Sort by Rating Show 12 Products. ![]() This cam requires performance valve springs due to its 650 lift and adjustable pushrods. When the belt change ultimately was done, the rear pulley wouldn't be changed a second time, unless it was years down the road, and well knackered again, so I'm thinking there's nothing to be lost by just changing the pulley on its own, for now. This is a good choice for larger displacement EVO builds with head and piston modifications utilizing a 10.8-11.3 compression. ![]() Replace the rear pulley, front pulley and belt, all at the same time.Īs the belt doesn't seem to be in imminent danger of failure, my view is just change the rear pulley now, and hold off on the belt change for a while, maybe a long while, rather than do all that invasive surgery, possibly for no benefit. JIMS USA JIM 2324 Sprocket Shaft Seal Installer JIM2324 Sprocket Shaft Seal Installer 2324Use on all Sportster® 1974-2003 &Buell ® 1987-02.Instruction Sheet No.2324-IS.Use this kit to install thesprocket shaft seal H-D®No.35151-74 to the properdepth, and also for holding the seal perfectly square,for a no leak fit. The shape and location of the lobe on the shaft determines when the valve opens, how high it lifts, when it closes, and how rapidly the valve movement takes place. The heavy-duty baseplate can be fixed in a vise and holds the flywheels with two studs for loosening or tightening the shaft and crank pin nuts. Top-quality Harley flywheel rebuilding jig. The purpose of a lobe is to open and close an intake or exhaust valve. Our service team will be glad to help out: Mondays - Thursdays 08:00-17:00 CET, Fridays 08:00-16:00 CET, Phone: +49 / 931 250 61 16, eMail:. Hope the belt is OK, and run it until it isn't.Ģ. Each camshaft includes one or more elliptical lobes welded or machined to the shaft. Fit the rear pulley, and do nothing else. I think Roy is buying a new rear pulley anyway, so the options (as I see it) are:ġ. Be careful not to damage the lip of the groove in the crankcase.Yes Kev, I think we may well be at cross purposes here. ![]() Slide the screwdriver tip around the edge of the bearing, lifting the retaining ring up and out of the groove. Fuel Tool Jims Kraus Moto Namz Custom Cycle Products Progressive Suspension S&S. Using the tip of a flat blade screwdriver, carefully lift the edge of the retaining ring up out of its groove in the crankcase. ![]() The left main bearing (1) is press-fit into the main bearing bore (2) in the left crankcase and secured with a retaining ring (3) on the inboard side. Instruction Sheet For Part No.1361G,1362G, 1363G, 1364G, 1361, 1362, 1363, & 1364 Rev B 6-15 JIMSEVOLUTION CAMSHAFT USE ON ALL EVO ENGINES 1984-1999 To complete our line of valve train components, JIMS now offers cam shafts. This tool is a work-in-progress and is not intended to substitute professional advice. Set thrust washer aside for inspection or reuse. No.1361-IS A Division of Thiessen Products, Inc. MGI SpeedWare’s camshaft calculator is a free tool made by and for car enthusiasts. Remove thrust washer from outboard side of crankcase half by pulling it past oil seal. Unbolt left crankcase half from stand and move it to bench area. While holding flywheel assembly so that it does not fall out of the left crankcase half, rotate bottom end assembly in engine stand so assembly is upright and flywheel shafts are horizontal.Ĭarefully slide flywheel assembly out of left crankcase and place it in a clean, safe place. The flywheel assembly can fall out, resulting in parts damage or moderate injury. Do not rotate crankcase half in engine stand when flywheel is installed. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |